Asst.sub Engineer model set 1
1. When the reduced level of the water source is higher then the reduced level of the consumer's place, water is generally supplied
a) by pumping system.
b) by gravitational system.
c) both (a) and (b)
d) all the above.
2. The process of passing water through beds of granular materials, is called
a) screening.
b) sedimentation.
c) filtration.
d) none of these.
3. 'Shrouding' is essentially provided in
a) strainer type wells.
b) cavity type wells.
c) slotted type wells.
d) all the above.
4. The maximum permissible hardness for public supplies is
a) 95 mg/liter.
b) 105 mg/liter.
c) 115 mg/liter.
d) 125 mg/liter.
5. In pumping stations, the type of joint generally used, is
a) socket and spigot joint.
b) flanged joint.
c) expansion joint.
d) dresser coupling joint.
6. The total domestic consumption in a city water supply, is assumed
a) 20%
b) 30%
c) 40%
d) 60%
7. Detailed plotting is generally done by
a) radiation.
b) traversing.
c) resection.
d) all of the above.
8. Subtense bar is an instrument used for
a) levelling.
b) measurement of horizontal distance in plane areas.
c) measurement of horizontal distance in undulated areas.
d) measurement of angels.
9. Two contour lines, having the same elevation
a) can not cross each other.
b) can cross each other.
c) can not unite together.
d) can unite together.
10. The vertical angle between longitudinal axis of a freely suspended magnetic needle and a horizontal line at its pivot, is known
a) declination.
b) azimuth.
c) dip.
d) bearing.
11. To orient a plane table at a point with two inaccessible points, the method generally adopted, is
a) intersection.
b) resection.
c) radiation.
d) two point problem.
12. Perpendicularity of an offset may be judged by eye, if the length of the offset is
a) 5m
b) 10m
c) 15m
d) 20m
13. In chain surveying tie lines are primarily provided
a) to check the accuracy of the survey.
b) to take offsets for details survey.
c) to avoid long offsets from chain lines.
d) to increase the number of chain lines.
14.The local swelling of a finished plaster,is termed
a)cracking. b)dubbing.
c)blistering. d)hacking.
15.The portion of a brick cut across the width,is called
a)closer. b)half brick.
c)bed. d)bat.
16.The dimensions of a queen closer,are
a) (19×9×9)cm b) (19×9×4.5)cm
c) (19×4.5×9)cm d) (1.8×4.5×9)cm
17.For plastering the exposed brick walls,the cement sand and mortar should be
a) 1:2 b)1:3
c)1:4 d)1:6
18.To construct a 10cm thick partition wall,you will prefer
a) English bond. b)Flemish bond.
c)Header bond d)Stretcher bond.
19.The mortar in which both cement and lime are used as binding materials,is called
a)cement mortar
b)lime mortar.
c)fire resistant mortar
d)gauged mortar.
20.The formwork from the sides of beams can be removed only after
a) 1 day . b) 4 days.
c) 7 days. d)14days.
21.The inner section of a cavity wall ,is generally known as
a)Buttress b)Leaf wall
c)Pilaster. d)Pillar
22.The under surface of and arc,is called
a)Soffit. b)Intrados.
c)Haunch. d)Back.
23.The maximum no.of steps in a flight should generally be restricted to
a)10 b)12
c)15 d)No limit.
24.Brick walls are measured in sq.m if the thickness of the wall is.
a) 10 cm b) 15 cm
c) 20 cm d) none of these.
25.While estimating the quantities for the construction of a building,the correct metric unit is:
a) Meter for length.
b)Cubic for the area.
c)Square meter for the volume.
d)Liter for capacity.
26.Cost of fittings and their fixing is specified for the following sanitary fittings
a)water closets. b)flushing pipes
c)lavatory basins. d)all the above.
27.The excavation exceeding 1.5m in width and 10 sq.m in plan area with a depth not exceeding 30 cm,is termed as
a)excavation over area b)surface dressing.
c)cutting. d)surface excavation.
28.The area is measured correct to the nearest
a)0.01 sq.m b)0.02 sq.m
c)0.03 sq.m d)0.04 sq.m
29.According to ISI method of measurement,the order of the sequence is
a)Length,breadth,height.
b)Breadth,length,height.
c)Height,length,breadth.
d)All of these.
30.The expected out turn of 12mm plastering with cement mortar is
a)2.5 sq.m b)4.0 sq.m
c) 6.0 sq.m d) 8.0 sq.m
31.The 'centre line method' is specially adopted for estimating
a)circular buildings. b)hexagonal buildings.
c)octagonal buildings. d)all of these.
32.Which of the following is the purest form of iron.
a)cast iron. b)wrought iron.
c)mild steel. d)high carbon steel.
33.Hydraulic lime is obtained by
a)Burning of lime stone.
b)Burning of kankar.
c)Adding water to quick lime.
d)Calcination of pure clay.
34.For testing compressive strength of cement,the size of cube used is
a) 50mm b) 70.6mm
c) 100mm d) 150mm
35.Gypsum is
a) mechanically formed sedimentary rock.
b) igneous rock.
c)chemically precipitated
sedimentary rock.
d)metamorphic rock.
36.The tendency of a stone is,to split along.
a)texture. b)fracture.
c)cleavage. d)structure.
37. Bitumen may be dissolved in
a) Carbon dioxide.
b) Water.
c) Sodium chloride.
d) Carbon di-sulphide.
38. The PVC doors and windows are preferred as they are
a) Rust proof. b) Rot proof.
c) Water proof. d) All of these.
39. The property by virtue of which lime sets under water, is known as
a) Slacking. b) Setting.
c) Hydraulicity. d) Calcining.
40. A stone is rejected if it absorbs water more than
a) 5% b) 10%
c) 15% d) 20%
41. French polish is
a) Oil paint. b) Distemper.
c) Spirit varnish. d) None of these.
42. Name the type of cement from the following for canal linings :
a) Sulphate resisting cement
b) Rapid hardening cement
c) Quick setting cement
d) Pozzolana cement
43. If cross slope of a country is greater than 60%,the terrain is classified as
a) Rolling. b) Mountainous.
c) Steep. d) Plain.
44. Driving vehicles on wet surfaced roads, is dangerous because it may
a) Skid. b) Slip.
c) Overturn. d) All the above.
45. Customers prefer parking of their vehicle at
a) 90° to aisles. b) 85° to aisles.
c) 80° to aisles d) 75° to aisles.
46. Minimum radius a simple circular curve in highway:
a) 15m b) 20m
c) 25m d) 12m
47. Which of the following is considered to be the highest quality construction in the group of black top pavements?
a) Mastic asphalt.
b) Sheet asphalt.
c) Bituminous carpet.
d) Bituminous concrete.
48. The most suitable equipment for
compacting clayey soil is a
a) Smooth wheeled roller.
b) Pneumatic tyred roller.
c) Sheep foot roller.
d) Vibrator.
49. In hill roads the side drains are provided;
a) Only on the hill side of road.
b) Only on the opposite side of hill.
c) On the both side of road.
d) None of the above.
50. In case of multi-lane road, overtaking is generally permitted;
a) From right.
b) From Left.
c) From both side right & left.
d) None of the above.
51. Cross regulators in main canals are provided;
a) To regulate water supply in the distributaries.
b) To increase water head upstream when a main canal is running with low supplies.
c) To overflow excessive flow water.
d) None of these.
52. The depth of rice root zone, is;
a) 50cm b) 60cm
c) 80cm d) 90cm
53. In the barrage, the crest level is kept;
a) Low with large gates.
b) High with large gates.
c) High with no gates
d) Low with no gates
54. The difference in level between the top of a bank and supply level in a canal, is called;
a) Berm. b) Free board.
c) Height of bank. d) None of these.
55. Groynes are generally built;
a) Perpendicular to the bank.
b) Inclined up stream up to 30°
c) Inclined downstream up to 30°
d) All the above.
56. The minimum free board in irrigation canal is;
a) 20cm b) 30cm
c) 50cm d) 60cm
57. For cereal crops the most commonly adopted method of irrigation, is;
a) Free following method.
b) Check method.
c) Furrow method.
d) Sprinkling method.
58. The Systems installed in buildings to make them comfortable, efficient and safe is called;
a) AC.
b) Building services.
c) Noise protection.
d) Mechanical Services.
59. Repairing and maintenance is easy in;
a) Conduit writing.
b) Cleat writing
c) Wooden casing and capping wiring.
d) CTS or TRS or PVC sheath wiring.
60. Which is the most type of wiring used in domestic applications?
a) Conduit wiring. b) Cleat writing.
c) Batten wiring. d) None of these.
61.MCB stand for;
a) Miniature Circuit Beaker.
b) Mono Circuit Beaker.
c) Mega Circuit Beaker.
d) None of the above.
62. Waste water from different sources like bathroom, kitchens and wash basins is called;
a) Sewage. b) Grabage.
c) Sullage. d) Discharge.
63. कुनै एक सथानबाट अर्को स्थानमा सरुवा भई जाने निजामति कर्मचारीले कति समय भित्र बरबुझारथ गर्नुपर्छ?
a) १ महिना भित्र b) २१ दिन भित्र
c) १५ दिन भित्र d) ७ दिन भित्र
64. Details drawings are used to ;
a) Show all the necessary information needed.
b)Show relevant partial.
c) Both of the above.
d) None of the above.
65. These drawings are given to contractors to perform work or manufacture individual parts;
a) Assembly details.
b) 3D drawings.
c) Working drawings.
d) Skeleton assemblies.
66. The length to higher ratio of a closed filled arrow head is?
a) 1:3 b) 3:1
c) 1:2 d) 2:1
67. The development of cylinder is a;
a) Triangle. b) Rectangle.
c) Square. d) Trapezium.
68. For drawing of small objects, the scale used is;
a) Enlarged. b) Full size.
c) Reducing. d) All the above.
69. The drawing for municipality is done at scale;
a) 1” = 8’ b) 1:50
c) 1:100 d) Both (a) & (c)
70. The area occupied by A3 (drawing sheet) is………… m2;
a) 1/2 b) 1/4
c) 1/8 d) 1/16
Visit us on Facebook group :-https://www.facebook.com/groups/428012155598366/?ref=share
Visit us on Facebook Page:-https://www.facebook.com/𝐍𝐚-𝐁𝐞𝐞𝐍-100203262354498/
Date:-2079/03/11
BY ADMIN
a) by pumping system.
b) by gravitational system.
c) both (a) and (b)
d) all the above.
2. The process of passing water through beds of granular materials, is called
a) screening.
b) sedimentation.
c) filtration.
d) none of these.
3. 'Shrouding' is essentially provided in
a) strainer type wells.
b) cavity type wells.
c) slotted type wells.
d) all the above.
4. The maximum permissible hardness for public supplies is
a) 95 mg/liter.
b) 105 mg/liter.
c) 115 mg/liter.
d) 125 mg/liter.
5. In pumping stations, the type of joint generally used, is
a) socket and spigot joint.
b) flanged joint.
c) expansion joint.
d) dresser coupling joint.
6. The total domestic consumption in a city water supply, is assumed
a) 20%
b) 30%
c) 40%
d) 60%
7. Detailed plotting is generally done by
a) radiation.
b) traversing.
c) resection.
d) all of the above.
8. Subtense bar is an instrument used for
a) levelling.
b) measurement of horizontal distance in plane areas.
c) measurement of horizontal distance in undulated areas.
d) measurement of angels.
9. Two contour lines, having the same elevation
a) can not cross each other.
b) can cross each other.
c) can not unite together.
d) can unite together.
10. The vertical angle between longitudinal axis of a freely suspended magnetic needle and a horizontal line at its pivot, is known
a) declination.
b) azimuth.
c) dip.
d) bearing.
11. To orient a plane table at a point with two inaccessible points, the method generally adopted, is
a) intersection.
b) resection.
c) radiation.
d) two point problem.
12. Perpendicularity of an offset may be judged by eye, if the length of the offset is
a) 5m
b) 10m
c) 15m
d) 20m
13. In chain surveying tie lines are primarily provided
a) to check the accuracy of the survey.
b) to take offsets for details survey.
c) to avoid long offsets from chain lines.
d) to increase the number of chain lines.
14.The local swelling of a finished plaster,is termed
a)cracking. b)dubbing.
c)blistering. d)hacking.
15.The portion of a brick cut across the width,is called
a)closer. b)half brick.
c)bed. d)bat.
16.The dimensions of a queen closer,are
a) (19×9×9)cm b) (19×9×4.5)cm
c) (19×4.5×9)cm d) (1.8×4.5×9)cm
17.For plastering the exposed brick walls,the cement sand and mortar should be
a) 1:2 b)1:3
c)1:4 d)1:6
18.To construct a 10cm thick partition wall,you will prefer
a) English bond. b)Flemish bond.
c)Header bond d)Stretcher bond.
19.The mortar in which both cement and lime are used as binding materials,is called
a)cement mortar
b)lime mortar.
c)fire resistant mortar
d)gauged mortar.
20.The formwork from the sides of beams can be removed only after
a) 1 day . b) 4 days.
c) 7 days. d)14days.
21.The inner section of a cavity wall ,is generally known as
a)Buttress b)Leaf wall
c)Pilaster. d)Pillar
22.The under surface of and arc,is called
a)Soffit. b)Intrados.
c)Haunch. d)Back.
23.The maximum no.of steps in a flight should generally be restricted to
a)10 b)12
c)15 d)No limit.
24.Brick walls are measured in sq.m if the thickness of the wall is.
a) 10 cm b) 15 cm
c) 20 cm d) none of these.
25.While estimating the quantities for the construction of a building,the correct metric unit is:
a) Meter for length.
b)Cubic for the area.
c)Square meter for the volume.
d)Liter for capacity.
26.Cost of fittings and their fixing is specified for the following sanitary fittings
a)water closets. b)flushing pipes
c)lavatory basins. d)all the above.
27.The excavation exceeding 1.5m in width and 10 sq.m in plan area with a depth not exceeding 30 cm,is termed as
a)excavation over area b)surface dressing.
c)cutting. d)surface excavation.
28.The area is measured correct to the nearest
a)0.01 sq.m b)0.02 sq.m
c)0.03 sq.m d)0.04 sq.m
29.According to ISI method of measurement,the order of the sequence is
a)Length,breadth,height.
b)Breadth,length,height.
c)Height,length,breadth.
d)All of these.
30.The expected out turn of 12mm plastering with cement mortar is
a)2.5 sq.m b)4.0 sq.m
c) 6.0 sq.m d) 8.0 sq.m
31.The 'centre line method' is specially adopted for estimating
a)circular buildings. b)hexagonal buildings.
c)octagonal buildings. d)all of these.
32.Which of the following is the purest form of iron.
a)cast iron. b)wrought iron.
c)mild steel. d)high carbon steel.
33.Hydraulic lime is obtained by
a)Burning of lime stone.
b)Burning of kankar.
c)Adding water to quick lime.
d)Calcination of pure clay.
34.For testing compressive strength of cement,the size of cube used is
a) 50mm b) 70.6mm
c) 100mm d) 150mm
35.Gypsum is
a) mechanically formed sedimentary rock.
b) igneous rock.
c)chemically precipitated
sedimentary rock.
d)metamorphic rock.
36.The tendency of a stone is,to split along.
a)texture. b)fracture.
c)cleavage. d)structure.
37. Bitumen may be dissolved in
a) Carbon dioxide.
b) Water.
c) Sodium chloride.
d) Carbon di-sulphide.
38. The PVC doors and windows are preferred as they are
a) Rust proof. b) Rot proof.
c) Water proof. d) All of these.
39. The property by virtue of which lime sets under water, is known as
a) Slacking. b) Setting.
c) Hydraulicity. d) Calcining.
40. A stone is rejected if it absorbs water more than
a) 5% b) 10%
c) 15% d) 20%
41. French polish is
a) Oil paint. b) Distemper.
c) Spirit varnish. d) None of these.
42. Name the type of cement from the following for canal linings :
a) Sulphate resisting cement
b) Rapid hardening cement
c) Quick setting cement
d) Pozzolana cement
43. If cross slope of a country is greater than 60%,the terrain is classified as
a) Rolling. b) Mountainous.
c) Steep. d) Plain.
44. Driving vehicles on wet surfaced roads, is dangerous because it may
a) Skid. b) Slip.
c) Overturn. d) All the above.
45. Customers prefer parking of their vehicle at
a) 90° to aisles. b) 85° to aisles.
c) 80° to aisles d) 75° to aisles.
46. Minimum radius a simple circular curve in highway:
a) 15m b) 20m
c) 25m d) 12m
47. Which of the following is considered to be the highest quality construction in the group of black top pavements?
a) Mastic asphalt.
b) Sheet asphalt.
c) Bituminous carpet.
d) Bituminous concrete.
48. The most suitable equipment for
compacting clayey soil is a
a) Smooth wheeled roller.
b) Pneumatic tyred roller.
c) Sheep foot roller.
d) Vibrator.
49. In hill roads the side drains are provided;
a) Only on the hill side of road.
b) Only on the opposite side of hill.
c) On the both side of road.
d) None of the above.
50. In case of multi-lane road, overtaking is generally permitted;
a) From right.
b) From Left.
c) From both side right & left.
d) None of the above.
51. Cross regulators in main canals are provided;
a) To regulate water supply in the distributaries.
b) To increase water head upstream when a main canal is running with low supplies.
c) To overflow excessive flow water.
d) None of these.
52. The depth of rice root zone, is;
a) 50cm b) 60cm
c) 80cm d) 90cm
53. In the barrage, the crest level is kept;
a) Low with large gates.
b) High with large gates.
c) High with no gates
d) Low with no gates
54. The difference in level between the top of a bank and supply level in a canal, is called;
a) Berm. b) Free board.
c) Height of bank. d) None of these.
55. Groynes are generally built;
a) Perpendicular to the bank.
b) Inclined up stream up to 30°
c) Inclined downstream up to 30°
d) All the above.
56. The minimum free board in irrigation canal is;
a) 20cm b) 30cm
c) 50cm d) 60cm
57. For cereal crops the most commonly adopted method of irrigation, is;
a) Free following method.
b) Check method.
c) Furrow method.
d) Sprinkling method.
58. The Systems installed in buildings to make them comfortable, efficient and safe is called;
a) AC.
b) Building services.
c) Noise protection.
d) Mechanical Services.
59. Repairing and maintenance is easy in;
a) Conduit writing.
b) Cleat writing
c) Wooden casing and capping wiring.
d) CTS or TRS or PVC sheath wiring.
60. Which is the most type of wiring used in domestic applications?
a) Conduit wiring. b) Cleat writing.
c) Batten wiring. d) None of these.
61.MCB stand for;
a) Miniature Circuit Beaker.
b) Mono Circuit Beaker.
c) Mega Circuit Beaker.
d) None of the above.
62. Waste water from different sources like bathroom, kitchens and wash basins is called;
a) Sewage. b) Grabage.
c) Sullage. d) Discharge.
63. कुनै एक सथानबाट अर्को स्थानमा सरुवा भई जाने निजामति कर्मचारीले कति समय भित्र बरबुझारथ गर्नुपर्छ?
a) १ महिना भित्र b) २१ दिन भित्र
c) १५ दिन भित्र d) ७ दिन भित्र
64. Details drawings are used to ;
a) Show all the necessary information needed.
b)Show relevant partial.
c) Both of the above.
d) None of the above.
65. These drawings are given to contractors to perform work or manufacture individual parts;
a) Assembly details.
b) 3D drawings.
c) Working drawings.
d) Skeleton assemblies.
66. The length to higher ratio of a closed filled arrow head is?
a) 1:3 b) 3:1
c) 1:2 d) 2:1
67. The development of cylinder is a;
a) Triangle. b) Rectangle.
c) Square. d) Trapezium.
68. For drawing of small objects, the scale used is;
a) Enlarged. b) Full size.
c) Reducing. d) All the above.
69. The drawing for municipality is done at scale;
a) 1” = 8’ b) 1:50
c) 1:100 d) Both (a) & (c)
70. The area occupied by A3 (drawing sheet) is………… m2;
a) 1/2 b) 1/4
c) 1/8 d) 1/16
Visit us on Facebook group :-https://www.facebook.com/groups/428012155598366/?ref=share
Visit us on Facebook Page:-https://www.facebook.com/𝐍𝐚-𝐁𝐞𝐞𝐍-100203262354498/
Date:-2079/03/11
BY ADMIN
Comments
Post a Comment